DATADSHEET
The NuMicro® M483 CAN series is a high performance, low power microcontroller powered by the Arm® Cortex®-M4F core with DSP extension. Running up to 192 MHz with 130 µA/MHz dynamic power consumption provides excellent energy efficiency. The 256 KB embedded Flash memory supports up to 4 configurable eXecute-Only-Memory regions, and the 128 KB embedded SRAM provides multi-level retention in standby power-down mode. The factory pre-loaded bootloader delivers Secure Boot functionality to check code integrity inside embedded Flash memory. One-Time Programmable ROM is also included for product life-cycle management.
The NuMicro® M483 CAN series supports operating voltage from 1.8V to 3.6V, and industrial operating temperature from -40°C to 105°C. It is integrated with two or three sets of CAN 2.0B interface, dual 12-bit 5 MSPS ADC, camera interface, USB full speed OTG with the crystal-less feature in device mode, and up to eight sets of high-speed UART interface. Package type includes LQFP64 and LQFP128.
Target Application:
Motor Control, Industrial Control, Battery Management System, EV Charging Pile, etc.
Key Features:
• |
Core |
|
- |
Up to 192 MHz Arm® Cortex ®-M4F delivering 1.25 DMIPS per MHz |
|
- |
DSP instruction set |
|
- |
Memory Protection Unit (MPU) |
|
|
• |
Memory |
|
- |
256 KB zero-wait state flash supports eXecute-Only-Memory (XOM) |
|
- |
128 KB RAM (with 32 KB hardware parity check) |
|
- |
2 KB OTP for general purpose |
|
|
• |
Cyclic Redundancy Calculation Unit |
|
|
• |
16-ch Peripheral DMA Controller |
|
|
• |
External Bus Interface |
|
- |
LCD parallel interface, i80 mode |
|
|
• |
Clocks |
|
- |
4 to 24 MHz crystal oscillator |
|
- |
32 kHz oscillator for RTC (variation < ±0.25%) |
|
- |
Internal 48 MHz RC oscillator (X-less) |
|
- |
Internal 12 MHz RC oscillator (variation < ±2%) |
|
- |
Internal 10 kHz RC with calibration |
|
|
• |
RTC |
|
- |
Independent VBAT power pin |
|
- |
80 bytes of battery-powered backup registers |
|
|
• |
Timer & PWM |
|
- |
Four 32-bit timers |
|
- |
Twelve Enhanced PWM with twelve 16-bit timers |
|
- |
Twelve Basic PWM with two 16-bit timers |
|
- |
One 24-bit count-down SysTick timer |
|
- |
One watchdog timer |
|
- |
One window watchdog timer |
|
• |
Analog |
|
- |
Two 12-bit, 5 MSPS SAR ADC (up to 24 channels) with 0 to analog supply conversion range |
|
- |
One 12-bit, 1 MSPS DAC |
|
- |
Two rail-to-rail comparators |
|
|
• |
Communication Interfaces |
|
- |
Up to 8 low power UART interfaces (17 Mbps), including 2 LIN interfaces |
|
- |
Up to 1 ISO-7816 interface (3.4 MHz), supporting full duplex UART mode |
|
- |
Three I²C interfaces (Up to 3.4 Mbps) |
|
- |
Two Quad-SPI interfaces (Up to 96 MHz) |
|
- |
Up to 3 SPI/I²S interfaces (SPI up to 96 MHz, I²S up to 192 kHz/16-bit) |
|
- |
One I²S interface (192 kHz/32-bit) |
|
- |
Up to 3 CAN 2.0B interfaces |
|
- |
One Secure Digital Host Controllers (50 MHz) |
|
|
• |
Control Interfaces |
|
- |
Two quadrature encoder interfaces (QEI) |
|
- |
Two 24-bit, 3-ch input capture timer/counter units |
|
|
|
• |
Camera interface |
|
- |
CMOS Sensor interface with hardware 1-bit luminance output |
|
|
• |
Advanced Connectivity |
|
- |
USB 2.0 full speed OTG controller with on-chip PHY |
|
|
|
• |
Operating Characteristics |
|
- |
Voltage range: 1.8V to 3.6V |
|
- |
Temperature range: -40°C to 105°C |
|
|
|
• |
IEC-60730 Class B compliance |
|
|
|
• |
Cryptography Accelerator |
|
- |
AES-256 |
|
- |
True random number generator |
|
For more details and documents, please link to Nuvoton Official Website GO