Arm Cortex-M4

M483KGCAE2A View larger


Add to my wishlist

M483KGCAE2A

Quantity Unit Price (USD)
1-999 2.77
1000-1999 2.51
2000-4999 2.42
5000+ Contact

More details

New

115 Items

$2.77

DATADSHEET

The NuMicro® M483 CAN series is a high performance, low power microcontroller powered by the Arm® Cortex®-M4F core with DSP extension. Running up to 192 MHz with 130 µA/MHz dynamic power consumption provides excellent energy efficiency. The 256 KB embedded Flash memory supports up to 4 configurable eXecute-Only-Memory regions, and the 128 KB embedded SRAM provides multi-level retention in standby power-down mode. The factory pre-loaded bootloader delivers Secure Boot functionality to check code integrity inside embedded Flash memory. One-Time Programmable ROM is also included for product life-cycle management.

The NuMicro® M483 CAN series supports operating voltage from 1.8V to 3.6V, and industrial operating temperature from -40°C to 105°C. It is integrated with two or three sets of CAN 2.0B interface, dual 12-bit 5 MSPS ADC, camera interface, USB full speed OTG with the crystal-less feature in device mode, and up to eight sets of high-speed UART interface. Package type includes LQFP64 and LQFP128.

Target Application:

Motor Control, Industrial Control, Battery Management System, EV Charging Pile, etc.

Key Features:

Core
  - Up to 192 MHz Arm® Cortex ®-M4F delivering 1.25 DMIPS per MHz
  - DSP instruction set
  - Memory Protection Unit (MPU)
   
Memory
  - 256 KB zero-wait state flash supports eXecute-Only-Memory (XOM)
  - 128 KB RAM (with 32 KB hardware parity check)
  - 2 KB OTP for general purpose
   
Cyclic Redundancy Calculation Unit
   
16-ch Peripheral DMA Controller
   
External Bus Interface
  - LCD parallel interface, i80 mode
   
Clocks
  - 4 to 24 MHz crystal oscillator
  - 32 kHz oscillator for RTC (variation < ±0.25%)
  - Internal 48 MHz RC oscillator (X-less)
  - Internal 12 MHz RC oscillator (variation < ±2%)
  - Internal 10 kHz RC with calibration
   
RTC
  - Independent VBAT power pin
  - 80 bytes of battery-powered backup registers
   
Timer & PWM
  - Four 32-bit timers
  - Twelve Enhanced PWM with twelve 16-bit timers
  - Twelve Basic PWM with two 16-bit timers
  - One 24-bit count-down SysTick timer
  - One watchdog timer
  - One window watchdog timer
Analog
  - Two 12-bit, 5 MSPS SAR ADC (up to 24 channels) with 0 to analog supply conversion range
  - One 12-bit, 1 MSPS DAC
  - Two rail-to-rail comparators
   
Communication Interfaces
  - Up to 8 low power UART interfaces (17 Mbps), including 2 LIN interfaces
  - Up to 1 ISO-7816 interface (3.4 MHz), supporting full duplex UART mode
  - Three I²C interfaces (Up to 3.4 Mbps)
  - Two Quad-SPI interfaces (Up to 96 MHz)
  - Up to 3 SPI/I²S interfaces (SPI up to 96 MHz, I²S up to 192 kHz/16-bit)
  - One I²S interface (192 kHz/32-bit)
  - Up to 3 CAN 2.0B interfaces
  - One Secure Digital Host Controllers (50 MHz)
   
Control Interfaces
  - Two quadrature encoder interfaces (QEI)
  - Two 24-bit, 3-ch input capture timer/counter units
     
Camera interface
  - CMOS Sensor interface with hardware 1-bit luminance output
   
Advanced Connectivity
  - USB 2.0 full speed OTG controller with on-chip PHY
     
Operating Characteristics
  - Voltage range: 1.8V to 3.6V
  - Temperature range: -40°C to 105°C
     
IEC-60730 Class B compliance
     
Cryptography Accelerator
  - AES-256
  - True random number generator


For more details and documents, please link to Nuvoton Official Website
GO

-

QuantityDiscountYou Save
10009.38%Up to$259.83
200012.5%Up to$692.50
Part No.M483KGCAE2A
Flash (Kbytes)256
SRAM (Kbytes)128
QEI2
DAC (12-bit)1-ch
PackageLQFP 128
ISP/ICP/IAP
USB 2.0 FS OTG
USB 2.0 HS OTG
Touch Key-
Tamper Detect (pin)6
Voltage Adjustable InterfaceY
Ethernet MAC-
Camera Interface1
OP Amp.-

30 other products in the same category:

Customers who bought this product also bought: