DATADSHEET
The M484KIDAE is a high performance, low power microcontroller powered by the Arm® Cortex®-M4F core with DSP extension. It can run up to 192 MHz with 175 µA/MHz dynamic low power consumption. The 512 KB embedded dual bank Flash memory supports OTA (Over-The-Air) firmware upgrade, and the 160 KB embedded SRAM includes 32 KB cache to speed up external SPI Flash code execution. The factory pre-loaded bootloader delivers Secure Boot functionality to provide the code integrity check in embedded Flash memory. The built-in Secure Protection ROM provides a safe space for saving confidential program or data. One-Time Programmable ROM is also included for product life-cycle management.
The M484KIDAE supports operating voltage from 1.8V to 3.6V, and industrial operating temperature from -40°C to 105°C. It is integrated with 2 sets of USB 2.0 interface with op-chip full speed and high speed OTG PHY. Package type is LQFP128.
Target Application:
USB Adapter, USB Sensor Hub, etc.
Key Features:
| • |
Core |
| |
- |
Up to 192 MHz Arm® Cortex ®-M4F delivering 1.25 DMIPS per MHz |
| |
- |
DSP instruction set |
| |
- |
Memory Protection Unit (MPU) |
| |
|
| • |
Memory |
| |
- |
512 KB zero-wait state Flash memory |
| |
- |
160 KB RAM, including 32 KB external SPI Flash cache |
| |
- |
4 KB Secure Protection ROM |
| |
- |
2 KB One-Time-Programmable ROM |
| |
|
| • |
Cyclic Redundancy Calculation Unit |
| |
|
| • |
16-ch Peripheral DMA Controller |
| |
|
| • |
External Bus Interface |
| |
- |
LCD parallel interface, i80 mode |
| |
|
| • |
Clocks |
| |
- |
4 to 24 MHz crystal oscillator |
| |
- |
32 kHz oscillator for RTC |
| |
- |
Internal 12 MHz RC oscillator |
| |
- |
Internal 10 kHz RC oscillator |
| |
- |
Internal PLL up to 480 MHz |
| |
|
| • |
RTC |
| |
- |
80 bytes of battery-powered backup registers |
| |
|
| • |
Timer & PWM |
| |
- |
Four 32-bit timers |
| |
- |
Twelve Enhanced PWM with twelve 16-bit timers |
| |
- |
Twelve Basic PWM with two 16-bit timers |
| |
- |
One 24-bit count-down SysTick timer |
| |
- |
One watchdog timer |
| |
- |
One window watchdog timer |
|
| • |
Analog Peripheral |
| |
- |
One 12-bit, up to 16-ch 5MSPS SAR ADC |
| |
- |
Two 12-bit, 1 MSPS DAC |
| |
- |
Two rail-to-rail comparators |
| |
- |
Three operational amplifiers |
| |
|
| • |
Communication Interface |
| |
- |
Up to 6 low power UART interfaces (17 Mbps), including 2 LIN interfaces |
| |
- |
Up to 3 ISO-7816 interfaces (3.4 MHz), supporting full duplex UART mode |
| |
- |
Three I²C interfaces (Up to 3.4 Mbps) |
| |
- |
One SPI Flash interface (Up to 96 MHz) supports quad mode |
| |
- |
One Quad-SPI interface (Up to 96 MHz) |
| |
- |
Up to 4 SPI/ I²S interfaces (SPI up to 96 MHz, I²S up to 192 kHz/16-bit) |
| |
- |
One I²S interface (192 kHz/32-bit) |
| |
- |
Two USCI interfaces, supporting configurable UART/ SPI/ I²C |
| |
- |
Two Secure Digital Host Controllers (50 MHz) |
| |
|
| • |
Control Interface |
| |
- |
Two quadrature encoder interfaces |
| |
- |
Two 24-bit, 3-ch input capture timer/counter units |
| |
|
| • |
Advanced Connectivity |
| |
- |
USB 2.0 high speed device/ host/ OTG controller with on-chip PHY |
| |
- |
USB 2.0 full speed device/ host/ OTG controller with on-chip PHY |
| |
|
|
| • |
Operating Characteristic |
| |
- |
Voltage range: 1.8V to 3.6V |
| |
- |
Temperature range: -40°C to +105°C |
|
For more details and documents, please link to Nuvoton Official Website GO
